^8f3ce5b39 (kx 2023-10-28 12:00:06 +0300 1) # SPDX-License-Identifier: GPL-2.0-only
^8f3ce5b39 (kx 2023-10-28 12:00:06 +0300 2) config MKISS
^8f3ce5b39 (kx 2023-10-28 12:00:06 +0300 3) tristate "Serial port KISS driver"
^8f3ce5b39 (kx 2023-10-28 12:00:06 +0300 4) depends on AX25 && TTY
^8f3ce5b39 (kx 2023-10-28 12:00:06 +0300 5) select CRC16
^8f3ce5b39 (kx 2023-10-28 12:00:06 +0300 6) help
^8f3ce5b39 (kx 2023-10-28 12:00:06 +0300 7) KISS is a protocol used for the exchange of data between a computer
^8f3ce5b39 (kx 2023-10-28 12:00:06 +0300 8) and a Terminal Node Controller (a small embedded system commonly
^8f3ce5b39 (kx 2023-10-28 12:00:06 +0300 9) used for networking over AX.25 amateur radio connections; it
^8f3ce5b39 (kx 2023-10-28 12:00:06 +0300 10) connects the computer's serial port with the radio's microphone
^8f3ce5b39 (kx 2023-10-28 12:00:06 +0300 11) input and speaker output).
^8f3ce5b39 (kx 2023-10-28 12:00:06 +0300 12)
^8f3ce5b39 (kx 2023-10-28 12:00:06 +0300 13) Although KISS is less advanced than the 6pack protocol, it has
^8f3ce5b39 (kx 2023-10-28 12:00:06 +0300 14) the advantage that it is already supported by most modern TNCs
^8f3ce5b39 (kx 2023-10-28 12:00:06 +0300 15) without the need for a firmware upgrade.
^8f3ce5b39 (kx 2023-10-28 12:00:06 +0300 16)
^8f3ce5b39 (kx 2023-10-28 12:00:06 +0300 17) To compile this driver as a module, choose M here: the module
^8f3ce5b39 (kx 2023-10-28 12:00:06 +0300 18) will be called mkiss.
^8f3ce5b39 (kx 2023-10-28 12:00:06 +0300 19)
^8f3ce5b39 (kx 2023-10-28 12:00:06 +0300 20) config 6PACK
^8f3ce5b39 (kx 2023-10-28 12:00:06 +0300 21) tristate "Serial port 6PACK driver"
^8f3ce5b39 (kx 2023-10-28 12:00:06 +0300 22) depends on AX25 && TTY
^8f3ce5b39 (kx 2023-10-28 12:00:06 +0300 23) help
^8f3ce5b39 (kx 2023-10-28 12:00:06 +0300 24) 6pack is a transmission protocol for the data exchange between your
^8f3ce5b39 (kx 2023-10-28 12:00:06 +0300 25) PC and your TNC (the Terminal Node Controller acts as a kind of
^8f3ce5b39 (kx 2023-10-28 12:00:06 +0300 26) modem connecting your computer's serial port to your radio's
^8f3ce5b39 (kx 2023-10-28 12:00:06 +0300 27) microphone input and speaker output). This protocol can be used as
^8f3ce5b39 (kx 2023-10-28 12:00:06 +0300 28) an alternative to KISS for networking over AX.25 amateur radio
^8f3ce5b39 (kx 2023-10-28 12:00:06 +0300 29) connections, but it has some extended functionality.
^8f3ce5b39 (kx 2023-10-28 12:00:06 +0300 30)
^8f3ce5b39 (kx 2023-10-28 12:00:06 +0300 31) Note that this driver is still experimental and might cause
^8f3ce5b39 (kx 2023-10-28 12:00:06 +0300 32) problems. For details about the features and the usage of the
^8f3ce5b39 (kx 2023-10-28 12:00:06 +0300 33) driver, read <file:Documentation/networking/6pack.rst>.
^8f3ce5b39 (kx 2023-10-28 12:00:06 +0300 34)
^8f3ce5b39 (kx 2023-10-28 12:00:06 +0300 35) To compile this driver as a module, choose M here: the module
^8f3ce5b39 (kx 2023-10-28 12:00:06 +0300 36) will be called 6pack.
^8f3ce5b39 (kx 2023-10-28 12:00:06 +0300 37)
^8f3ce5b39 (kx 2023-10-28 12:00:06 +0300 38) config BPQETHER
^8f3ce5b39 (kx 2023-10-28 12:00:06 +0300 39) tristate "BPQ Ethernet driver"
^8f3ce5b39 (kx 2023-10-28 12:00:06 +0300 40) depends on AX25
^8f3ce5b39 (kx 2023-10-28 12:00:06 +0300 41) help
^8f3ce5b39 (kx 2023-10-28 12:00:06 +0300 42) AX.25 is the protocol used for computer communication over amateur
^8f3ce5b39 (kx 2023-10-28 12:00:06 +0300 43) radio. If you say Y here, you will be able to send and receive AX.25
^8f3ce5b39 (kx 2023-10-28 12:00:06 +0300 44) traffic over Ethernet (also called "BPQ AX.25"), which could be
^8f3ce5b39 (kx 2023-10-28 12:00:06 +0300 45) useful if some other computer on your local network has a direct
^8f3ce5b39 (kx 2023-10-28 12:00:06 +0300 46) amateur radio connection.
^8f3ce5b39 (kx 2023-10-28 12:00:06 +0300 47)
^8f3ce5b39 (kx 2023-10-28 12:00:06 +0300 48) config DMASCC
^8f3ce5b39 (kx 2023-10-28 12:00:06 +0300 49) tristate "High-speed (DMA) SCC driver for AX.25"
^8f3ce5b39 (kx 2023-10-28 12:00:06 +0300 50) depends on ISA && AX25 && BROKEN_ON_SMP && ISA_DMA_API
^8f3ce5b39 (kx 2023-10-28 12:00:06 +0300 51) help
^8f3ce5b39 (kx 2023-10-28 12:00:06 +0300 52) This is a driver for high-speed SCC boards, i.e. those supporting
^8f3ce5b39 (kx 2023-10-28 12:00:06 +0300 53) DMA on one port. You usually use those boards to connect your
^8f3ce5b39 (kx 2023-10-28 12:00:06 +0300 54) computer to an amateur radio modem (such as the WA4DSY 56kbps
^8f3ce5b39 (kx 2023-10-28 12:00:06 +0300 55) modem), in order to send and receive AX.25 packet radio network
^8f3ce5b39 (kx 2023-10-28 12:00:06 +0300 56) traffic.
^8f3ce5b39 (kx 2023-10-28 12:00:06 +0300 57)
^8f3ce5b39 (kx 2023-10-28 12:00:06 +0300 58) Currently, this driver supports Ottawa PI/PI2, Paccomm/Gracilis
^8f3ce5b39 (kx 2023-10-28 12:00:06 +0300 59) PackeTwin, and S5SCC/DMA boards. They are detected automatically.
^8f3ce5b39 (kx 2023-10-28 12:00:06 +0300 60) If you have one of these cards, say Y here and read the AX25-HOWTO,
^8f3ce5b39 (kx 2023-10-28 12:00:06 +0300 61) available from <http://www.tldp.org/docs.html#howto>.
^8f3ce5b39 (kx 2023-10-28 12:00:06 +0300 62)
^8f3ce5b39 (kx 2023-10-28 12:00:06 +0300 63) This driver can operate multiple boards simultaneously. If you
^8f3ce5b39 (kx 2023-10-28 12:00:06 +0300 64) compile it as a module (by saying M instead of Y), it will be called
^8f3ce5b39 (kx 2023-10-28 12:00:06 +0300 65) dmascc. If you don't pass any parameter to the driver, all
^8f3ce5b39 (kx 2023-10-28 12:00:06 +0300 66) possible I/O addresses are probed. This could irritate other devices
^8f3ce5b39 (kx 2023-10-28 12:00:06 +0300 67) that are currently not in use. You may specify the list of addresses
^8f3ce5b39 (kx 2023-10-28 12:00:06 +0300 68) to be probed by "dmascc.io=addr1,addr2,..." (when compiled into the
^8f3ce5b39 (kx 2023-10-28 12:00:06 +0300 69) kernel image) or "io=addr1,addr2,..." (when loaded as a module). The
^8f3ce5b39 (kx 2023-10-28 12:00:06 +0300 70) network interfaces will be called dmascc0 and dmascc1 for the board
^8f3ce5b39 (kx 2023-10-28 12:00:06 +0300 71) detected first, dmascc2 and dmascc3 for the second one, and so on.
^8f3ce5b39 (kx 2023-10-28 12:00:06 +0300 72)
^8f3ce5b39 (kx 2023-10-28 12:00:06 +0300 73) Before you configure each interface with ifconfig, you MUST set
^8f3ce5b39 (kx 2023-10-28 12:00:06 +0300 74) certain parameters, such as channel access timing, clock mode, and
^8f3ce5b39 (kx 2023-10-28 12:00:06 +0300 75) DMA channel. This is accomplished with a small utility program,
^8f3ce5b39 (kx 2023-10-28 12:00:06 +0300 76) dmascc_cfg, available at
^8f3ce5b39 (kx 2023-10-28 12:00:06 +0300 77) <http://www.linux-ax25.org/wiki/Ax25-tools>. Please be sure to
^8f3ce5b39 (kx 2023-10-28 12:00:06 +0300 78) get at least version 1.27 of dmascc_cfg, as older versions will not
^8f3ce5b39 (kx 2023-10-28 12:00:06 +0300 79) work with the current driver.
^8f3ce5b39 (kx 2023-10-28 12:00:06 +0300 80)
^8f3ce5b39 (kx 2023-10-28 12:00:06 +0300 81) config SCC
^8f3ce5b39 (kx 2023-10-28 12:00:06 +0300 82) tristate "Z8530 SCC driver"
^8f3ce5b39 (kx 2023-10-28 12:00:06 +0300 83) depends on ISA && AX25 && ISA_DMA_API
^8f3ce5b39 (kx 2023-10-28 12:00:06 +0300 84) help
^8f3ce5b39 (kx 2023-10-28 12:00:06 +0300 85) These cards are used to connect your Linux box to an amateur radio
^8f3ce5b39 (kx 2023-10-28 12:00:06 +0300 86) in order to communicate with other computers. If you want to use
^8f3ce5b39 (kx 2023-10-28 12:00:06 +0300 87) this, read
^8f3ce5b39 (kx 2023-10-28 12:00:06 +0300 88) <file:Documentation/networking/device_drivers/hamradio/z8530drv.rst>
^8f3ce5b39 (kx 2023-10-28 12:00:06 +0300 89) and the AX25-HOWTO, available from
^8f3ce5b39 (kx 2023-10-28 12:00:06 +0300 90) <http://www.tldp.org/docs.html#howto>. Also make sure to say Y
^8f3ce5b39 (kx 2023-10-28 12:00:06 +0300 91) to "Amateur Radio AX.25 Level 2" support.
^8f3ce5b39 (kx 2023-10-28 12:00:06 +0300 92)
^8f3ce5b39 (kx 2023-10-28 12:00:06 +0300 93) To compile this driver as a module, choose M here: the module
^8f3ce5b39 (kx 2023-10-28 12:00:06 +0300 94) will be called scc.
^8f3ce5b39 (kx 2023-10-28 12:00:06 +0300 95)
^8f3ce5b39 (kx 2023-10-28 12:00:06 +0300 96) config SCC_DELAY
^8f3ce5b39 (kx 2023-10-28 12:00:06 +0300 97) bool "additional delay for PA0HZP OptoSCC compatible boards"
^8f3ce5b39 (kx 2023-10-28 12:00:06 +0300 98) depends on SCC
^8f3ce5b39 (kx 2023-10-28 12:00:06 +0300 99) help
^8f3ce5b39 (kx 2023-10-28 12:00:06 +0300 100) Say Y here if you experience problems with the SCC driver not
^8f3ce5b39 (kx 2023-10-28 12:00:06 +0300 101) working properly; please read
^8f3ce5b39 (kx 2023-10-28 12:00:06 +0300 102) <file:Documentation/networking/device_drivers/hamradio/z8530drv.rst>
^8f3ce5b39 (kx 2023-10-28 12:00:06 +0300 103) for details.
^8f3ce5b39 (kx 2023-10-28 12:00:06 +0300 104)
^8f3ce5b39 (kx 2023-10-28 12:00:06 +0300 105) If unsure, say N.
^8f3ce5b39 (kx 2023-10-28 12:00:06 +0300 106)
^8f3ce5b39 (kx 2023-10-28 12:00:06 +0300 107) config SCC_TRXECHO
^8f3ce5b39 (kx 2023-10-28 12:00:06 +0300 108) bool "support for TRX that feedback the tx signal to rx"
^8f3ce5b39 (kx 2023-10-28 12:00:06 +0300 109) depends on SCC
^8f3ce5b39 (kx 2023-10-28 12:00:06 +0300 110) help
^8f3ce5b39 (kx 2023-10-28 12:00:06 +0300 111) Some transmitters feed the transmitted signal back to the receive
^8f3ce5b39 (kx 2023-10-28 12:00:06 +0300 112) line. Say Y here to foil this by explicitly disabling the receiver
^8f3ce5b39 (kx 2023-10-28 12:00:06 +0300 113) during data transmission.
^8f3ce5b39 (kx 2023-10-28 12:00:06 +0300 114)
^8f3ce5b39 (kx 2023-10-28 12:00:06 +0300 115) If in doubt, say Y.
^8f3ce5b39 (kx 2023-10-28 12:00:06 +0300 116)
^8f3ce5b39 (kx 2023-10-28 12:00:06 +0300 117) config BAYCOM_SER_FDX
^8f3ce5b39 (kx 2023-10-28 12:00:06 +0300 118) tristate "BAYCOM ser12 fullduplex driver for AX.25"
^8f3ce5b39 (kx 2023-10-28 12:00:06 +0300 119) depends on AX25 && !S390
^8f3ce5b39 (kx 2023-10-28 12:00:06 +0300 120) select CRC_CCITT
^8f3ce5b39 (kx 2023-10-28 12:00:06 +0300 121) help
^8f3ce5b39 (kx 2023-10-28 12:00:06 +0300 122) This is one of two drivers for Baycom style simple amateur radio
^8f3ce5b39 (kx 2023-10-28 12:00:06 +0300 123) modems that connect to a serial interface. The driver supports the
^8f3ce5b39 (kx 2023-10-28 12:00:06 +0300 124) ser12 design in full-duplex mode. In addition, it allows the
^8f3ce5b39 (kx 2023-10-28 12:00:06 +0300 125) baudrate to be set between 300 and 4800 baud (however not all modems
^8f3ce5b39 (kx 2023-10-28 12:00:06 +0300 126) support all baudrates). This is the preferred driver. The next
^8f3ce5b39 (kx 2023-10-28 12:00:06 +0300 127) driver, "BAYCOM ser12 half-duplex driver for AX.25" is the old
^8f3ce5b39 (kx 2023-10-28 12:00:06 +0300 128) driver and still provided in case this driver does not work with
^8f3ce5b39 (kx 2023-10-28 12:00:06 +0300 129) your serial interface chip. To configure the driver, use the sethdlc
^8f3ce5b39 (kx 2023-10-28 12:00:06 +0300 130) utility available in the standard ax25 utilities package. For
^8f3ce5b39 (kx 2023-10-28 12:00:06 +0300 131) information on the modems, see <http://www.baycom.de/> and
^8f3ce5b39 (kx 2023-10-28 12:00:06 +0300 132) <file:Documentation/networking/device_drivers/hamradio/baycom.rst>.
^8f3ce5b39 (kx 2023-10-28 12:00:06 +0300 133)
^8f3ce5b39 (kx 2023-10-28 12:00:06 +0300 134) To compile this driver as a module, choose M here: the module
^8f3ce5b39 (kx 2023-10-28 12:00:06 +0300 135) will be called baycom_ser_fdx. This is recommended.
^8f3ce5b39 (kx 2023-10-28 12:00:06 +0300 136)
^8f3ce5b39 (kx 2023-10-28 12:00:06 +0300 137) config BAYCOM_SER_HDX
^8f3ce5b39 (kx 2023-10-28 12:00:06 +0300 138) tristate "BAYCOM ser12 halfduplex driver for AX.25"
^8f3ce5b39 (kx 2023-10-28 12:00:06 +0300 139) depends on AX25 && !S390
^8f3ce5b39 (kx 2023-10-28 12:00:06 +0300 140) select CRC_CCITT
^8f3ce5b39 (kx 2023-10-28 12:00:06 +0300 141) help
^8f3ce5b39 (kx 2023-10-28 12:00:06 +0300 142) This is one of two drivers for Baycom style simple amateur radio
^8f3ce5b39 (kx 2023-10-28 12:00:06 +0300 143) modems that connect to a serial interface. The driver supports the
^8f3ce5b39 (kx 2023-10-28 12:00:06 +0300 144) ser12 design in half-duplex mode. This is the old driver. It is
^8f3ce5b39 (kx 2023-10-28 12:00:06 +0300 145) still provided in case your serial interface chip does not work with
^8f3ce5b39 (kx 2023-10-28 12:00:06 +0300 146) the full-duplex driver. This driver is deprecated. To configure
^8f3ce5b39 (kx 2023-10-28 12:00:06 +0300 147) the driver, use the sethdlc utility available in the standard ax25
^8f3ce5b39 (kx 2023-10-28 12:00:06 +0300 148) utilities package. For information on the modems, see
^8f3ce5b39 (kx 2023-10-28 12:00:06 +0300 149) <http://www.baycom.de/> and
^8f3ce5b39 (kx 2023-10-28 12:00:06 +0300 150) <file:Documentation/networking/device_drivers/hamradio/baycom.rst>.
^8f3ce5b39 (kx 2023-10-28 12:00:06 +0300 151)
^8f3ce5b39 (kx 2023-10-28 12:00:06 +0300 152) To compile this driver as a module, choose M here: the module
^8f3ce5b39 (kx 2023-10-28 12:00:06 +0300 153) will be called baycom_ser_hdx. This is recommended.
^8f3ce5b39 (kx 2023-10-28 12:00:06 +0300 154)
^8f3ce5b39 (kx 2023-10-28 12:00:06 +0300 155) config BAYCOM_PAR
^8f3ce5b39 (kx 2023-10-28 12:00:06 +0300 156) tristate "BAYCOM picpar and par96 driver for AX.25"
^8f3ce5b39 (kx 2023-10-28 12:00:06 +0300 157) depends on PARPORT && AX25
^8f3ce5b39 (kx 2023-10-28 12:00:06 +0300 158) select CRC_CCITT
^8f3ce5b39 (kx 2023-10-28 12:00:06 +0300 159) help
^8f3ce5b39 (kx 2023-10-28 12:00:06 +0300 160) This is a driver for Baycom style simple amateur radio modems that
^8f3ce5b39 (kx 2023-10-28 12:00:06 +0300 161) connect to a parallel interface. The driver supports the picpar and
^8f3ce5b39 (kx 2023-10-28 12:00:06 +0300 162) par96 designs. To configure the driver, use the sethdlc utility
^8f3ce5b39 (kx 2023-10-28 12:00:06 +0300 163) available in the standard ax25 utilities package. For information on
^8f3ce5b39 (kx 2023-10-28 12:00:06 +0300 164) the modems, see <http://www.baycom.de/> and the file
^8f3ce5b39 (kx 2023-10-28 12:00:06 +0300 165) <file:Documentation/networking/device_drivers/hamradio/baycom.rst>.
^8f3ce5b39 (kx 2023-10-28 12:00:06 +0300 166)
^8f3ce5b39 (kx 2023-10-28 12:00:06 +0300 167) To compile this driver as a module, choose M here: the module
^8f3ce5b39 (kx 2023-10-28 12:00:06 +0300 168) will be called baycom_par. This is recommended.
^8f3ce5b39 (kx 2023-10-28 12:00:06 +0300 169)
^8f3ce5b39 (kx 2023-10-28 12:00:06 +0300 170) config BAYCOM_EPP
^8f3ce5b39 (kx 2023-10-28 12:00:06 +0300 171) tristate "BAYCOM epp driver for AX.25"
^8f3ce5b39 (kx 2023-10-28 12:00:06 +0300 172) depends on PARPORT && AX25 && !64BIT
^8f3ce5b39 (kx 2023-10-28 12:00:06 +0300 173) select CRC_CCITT
^8f3ce5b39 (kx 2023-10-28 12:00:06 +0300 174) help
^8f3ce5b39 (kx 2023-10-28 12:00:06 +0300 175) This is a driver for Baycom style simple amateur radio modems that
^8f3ce5b39 (kx 2023-10-28 12:00:06 +0300 176) connect to a parallel interface. The driver supports the EPP
^8f3ce5b39 (kx 2023-10-28 12:00:06 +0300 177) designs. To configure the driver, use the sethdlc utility available
^8f3ce5b39 (kx 2023-10-28 12:00:06 +0300 178) in the standard ax25 utilities package. For information on the
^8f3ce5b39 (kx 2023-10-28 12:00:06 +0300 179) modems, see <http://www.baycom.de/> and the file
^8f3ce5b39 (kx 2023-10-28 12:00:06 +0300 180) <file:Documentation/networking/device_drivers/hamradio/baycom.rst>.
^8f3ce5b39 (kx 2023-10-28 12:00:06 +0300 181)
^8f3ce5b39 (kx 2023-10-28 12:00:06 +0300 182) To compile this driver as a module, choose M here: the module
^8f3ce5b39 (kx 2023-10-28 12:00:06 +0300 183) will be called baycom_epp. This is recommended.
^8f3ce5b39 (kx 2023-10-28 12:00:06 +0300 184)
^8f3ce5b39 (kx 2023-10-28 12:00:06 +0300 185) config YAM
^8f3ce5b39 (kx 2023-10-28 12:00:06 +0300 186) tristate "YAM driver for AX.25"
^8f3ce5b39 (kx 2023-10-28 12:00:06 +0300 187) depends on AX25 && !S390
^8f3ce5b39 (kx 2023-10-28 12:00:06 +0300 188) help
^8f3ce5b39 (kx 2023-10-28 12:00:06 +0300 189) The YAM is a modem for packet radio which connects to the serial
^8f3ce5b39 (kx 2023-10-28 12:00:06 +0300 190) port and includes some of the functions of a Terminal Node
^8f3ce5b39 (kx 2023-10-28 12:00:06 +0300 191) Controller. If you have one of those, say Y here.
^8f3ce5b39 (kx 2023-10-28 12:00:06 +0300 192)
^8f3ce5b39 (kx 2023-10-28 12:00:06 +0300 193) To compile this driver as a module, choose M here: the module
^8f3ce5b39 (kx 2023-10-28 12:00:06 +0300 194) will be called yam.
^8f3ce5b39 (kx 2023-10-28 12:00:06 +0300 195)
^8f3ce5b39 (kx 2023-10-28 12:00:06 +0300 196)
Orange Pi5 kernel
Deprecated Linux kernel 5.10.110 for OrangePi 5/5B/5+ boards
3 Commits
0 Branches
0 Tags