Orange Pi5 kernel

^8f3ce5b39 (kx 2023-10-28 12:00:06 +0300  1) Samsung S5K6A3(YX) raw image sensor
^8f3ce5b39 (kx 2023-10-28 12:00:06 +0300  2) ---------------------------------
^8f3ce5b39 (kx 2023-10-28 12:00:06 +0300  3) 
^8f3ce5b39 (kx 2023-10-28 12:00:06 +0300  4) S5K6A3(YX) is a raw image sensor with MIPI CSI-2 and CCP2 image data interfaces
^8f3ce5b39 (kx 2023-10-28 12:00:06 +0300  5) and CCI (I2C compatible) control bus.
^8f3ce5b39 (kx 2023-10-28 12:00:06 +0300  6) 
^8f3ce5b39 (kx 2023-10-28 12:00:06 +0300  7) Required properties:
^8f3ce5b39 (kx 2023-10-28 12:00:06 +0300  8) 
^8f3ce5b39 (kx 2023-10-28 12:00:06 +0300  9) - compatible	: "samsung,s5k6a3";
^8f3ce5b39 (kx 2023-10-28 12:00:06 +0300 10) - reg		: I2C slave address of the sensor;
^8f3ce5b39 (kx 2023-10-28 12:00:06 +0300 11) - svdda-supply	: core voltage supply;
^8f3ce5b39 (kx 2023-10-28 12:00:06 +0300 12) - svddio-supply	: I/O voltage supply;
^8f3ce5b39 (kx 2023-10-28 12:00:06 +0300 13) - afvdd-supply	: AF (actuator) voltage supply;
^8f3ce5b39 (kx 2023-10-28 12:00:06 +0300 14) - gpios		: specifier of a GPIO connected to the RESET pin;
^8f3ce5b39 (kx 2023-10-28 12:00:06 +0300 15) - clocks	: should contain list of phandle and clock specifier pairs
^8f3ce5b39 (kx 2023-10-28 12:00:06 +0300 16) 		  according to common clock bindings for the clocks described
^8f3ce5b39 (kx 2023-10-28 12:00:06 +0300 17) 		  in the clock-names property;
^8f3ce5b39 (kx 2023-10-28 12:00:06 +0300 18) - clock-names	: should contain "extclk" entry for the sensor's EXTCLK clock;
^8f3ce5b39 (kx 2023-10-28 12:00:06 +0300 19) 
^8f3ce5b39 (kx 2023-10-28 12:00:06 +0300 20) Optional properties:
^8f3ce5b39 (kx 2023-10-28 12:00:06 +0300 21) 
^8f3ce5b39 (kx 2023-10-28 12:00:06 +0300 22) - clock-frequency : the frequency at which the "extclk" clock should be
^8f3ce5b39 (kx 2023-10-28 12:00:06 +0300 23) 		    configured to operate, in Hz; if this property is not
^8f3ce5b39 (kx 2023-10-28 12:00:06 +0300 24) 		    specified default 24 MHz value will be used.
^8f3ce5b39 (kx 2023-10-28 12:00:06 +0300 25) 
^8f3ce5b39 (kx 2023-10-28 12:00:06 +0300 26) The common video interfaces bindings (see video-interfaces.txt) should be
^8f3ce5b39 (kx 2023-10-28 12:00:06 +0300 27) used to specify link to the image data receiver. The S5K6A3(YX) device
^8f3ce5b39 (kx 2023-10-28 12:00:06 +0300 28) node should contain one 'port' child node with an 'endpoint' subnode.
^8f3ce5b39 (kx 2023-10-28 12:00:06 +0300 29) 
^8f3ce5b39 (kx 2023-10-28 12:00:06 +0300 30) Following properties are valid for the endpoint node:
^8f3ce5b39 (kx 2023-10-28 12:00:06 +0300 31) 
^8f3ce5b39 (kx 2023-10-28 12:00:06 +0300 32) - data-lanes : (optional) specifies MIPI CSI-2 data lanes as covered in
^8f3ce5b39 (kx 2023-10-28 12:00:06 +0300 33)   video-interfaces.txt.  The sensor supports only one data lane.